Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller


Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Price: US$63.99
Free Shipping





Eachine QX100 100mm Micro FPV Racing Quadcopter with 800TVL Camera BNF Based On F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller
Eachine QX100 100mm Micro FPV Racing Quadcopter 800TVL Camera BNF Based F3 Frsky Flight Controller

Spare Parts for Eachine QX100 Racing Quadcopter, Click Here!

Item Name Specification
Eachine QX100 Brand Name: Eachine
Wheelbase: 100mm
Weight: 41g (Exclude battery)
Size: 118*118*55mm
Flight controller: F3+Frsky Brush Flight Controller
Motor: 8520 Brush Motor
Propeller Size: 55mm
Camera: 800TVL HD CMOS 1/4 inch Camera
AV Wireless Transmitter: 5.8g 25mw 40ch
Batterry: 3.7V 600mah 30C Lipo battery
Flight time: 5-6 minutes
FPV Camera Sensor: 1/3 "CMOS
Lens: M8 800TVL Lens
Angle: 150 ° FOV horizontal viewing angle of 170 ° DFOV diagonal perspective
Format: NTSC / PAL (switchable)
Power: 3.6-5.5V
Transmitter Support video format: NTSC / PAL
Output Impedance: 75 Ohm
Output signal strength: 12 ~ 14dBm
Output Power: 25mW
Wireless Channel: 40CH
Operating voltage: 3.6V ~ 5.5V
Current: 100mA
Audio carrier: 6.5MHz
Weight: 6.8g

Frequency Table
Frequency Band A 5865 5845 5825 5805 5785 5765 5745 5725
Frequency Band B 5733 5752 5771 5790 5809 5828 5847 5866
Frequency Band E 5705 5685 5665 5645 5885 5905 5925 5945
Frequency Band F 5740 5760 5780 5800 5820 5840 5860 5880
Frequency Band R 5658 5695 5732 5769 5806 5843 5880 5917
Flight Control Board 1.F3 flight control is a open-source flight controller, support Cleanflight and Baseflight
2.This Flight Controller integrated the FRSKY Compatible 8CH receiver(Serial port output). Support FRSKY protocol 8CH.
3. It is integrated with DCDC voltage booster circuit, can supply power for other device through IIC and UART port. It support 1s and 2s Lipo battery.
4.Frequency for driving motor: 2000 (the frequency can be set up by user, max frequency can be 32K)
5.Attached gyro, support manual mode, horizontal mode
6.The firmware can be upgraded and adjusted by Micro-USB, the parameter adjustment interface is Baseflight-Configuration and Cleanflight-Configuration
Features Flight control base on F3, high current MOS output, convenient according to the personal touch.
It is open-source flight controller, can be according to the player's personal preferences,adjust the stability, convenient for different levels of players
Ready to fly, do not have to assemble and debug
The user only need to be equipped with a remote control and a receiver to experience the indoor FPV flight.
RaceBand, VTX CAM 40CH transmitter, Cmos 1/3 800Tvl HD camera, NTSC/PAL Format can be switch.

Station configuration:
1.Software to configure the UART3 to Serial RX, while RX_SERIAL change the Receiver mode, and select the SBUS.
2.Inside the CLI command interface, enter the SET motor_pwm_rate=1000, press Enter, and then type SAVE and then press enter to save.

Receiver Binding:
1.You can choose to FRSKY tuner on the remote control (Remote support plus tuner).
2.FRSKY X9D available remote control select D8 to enter Setup mode, receiver button and then select bind press the ENT key,To receive access to electricity,the receiver blue lights stay lit, release the receiver button, the blue lights of the receiver.
(NOTE : At this point, the receiver lights, is setting out to protect, set the remote control you need to set access control protection set, it is recommended that the mini throttle position, unlock the lock switch, model in self – stabilized mode.)
3.Press the ENT key to select Bind, and at this point, the blue light starts to flash the receiver and receiver power on again, the blue lights stay lit, indicating has good frequency.

Package included:
1 x QX100 Carbon Fibre Frame kit
4 x 8520 Coreless Motor
1 x F3 with Frsky Flight Controller
1 x 5.8G VTX w/Camera antenna
8 x 55mm Propeller
1 x 3.7V 600mah Battery
1 x Charging cable
1 x Paddle propeller

You Might Also Like: